1.0.2.91:

Added: - Active suspension calibration (available in the commercial version only) - Status and calibration of body position sensors - Ability to view configuration history without connecting to the vehicle - Vehicle market - Vehicle software version - Data Identifiers (DID) for the SUM module - Images of Polestar 1 and Polestar 2 vehicles - Battery charge level Fixed: - Optimized headlight module programming algorithm - Display of parking brake status on fully electric vehicles - Multiple fixes related to stability and communication with the vehicle

1.0.2.46:

- Fixed CSD (multimedia screen) freezing on certain software versions while reading the private modules list. Recommended for all users to update.

1.0.2.40:

- Major technical changes related to communication with the vehicle, especially broadcast requests. This process is now handled more correctly. - Full-fledged module reading has been added for modules that are not read directly and therefore could previously appear in gray in the list (BMS, OHC, GSM, IMS, BBS, WPC). - A content selection window has been added to the diagnostic report printing feature. Now, for example, you can print only the list of modules and software or just the list of errors. - In the mileage report window, which retrieves data from vehicle modules, new mileage sources have been added. Additionally, a red marker is now displayed if the vehicle reports about unwinded mileage. - Database update – new error codes have been added. - Added mileage unit setting (km/miles). There is also an "auto" mode, where the mileage is displayed in the same units as in the vehicle - The headlight configuration window has been redesigned based on feedback. - SOC/SOH display for high-voltage batteries has been added for fully electric vehicles. - A brake pedal adaptation reset feature has been added.

1.0.2.10:

- Added details for DTC diagnostics, where you can view the date and time of the error occurrence, mileage, and other useful information provided by the control unit. - 'Reset mode' has been added to the DTC erasing functionality. Sometimes ECU DTC cannot be erased during the current operating cycle, so the module is rebooted, and the error is cleared again automatically. Exceptions include SRS, VCM, VGM, IHU, and CSD modules for iCUP vehicles, which are not rebooted automatically. Errors must be cleared with the engine turned off in Inactive / Convenience / Active modes. In Driving mode, automatic module reboot does not occur, and some errors may not be cleared. - Active grille adaptation has been added. - Data Identifiers (DID) have been added for the ASDM module. - Improved the headlamp module configuration dialog (HCML/HCMR), new loaders added. - Added a restriction to prevent the unlocking of the parking heater if it is not locked. - The list of electronic modules in the diagnostics section is now displayed in alphabetical order.

1.0.2.2:

- HCM modules programming - Improved giagnostic functions for VGM cars - Improved IMMO PIN resolving algorithm - Stability enhancements

1.0.1.346:

- Added ASDM camera / radar adaptation reset - Added DIDs for BECM module - Configuration history - Minor stability enhancements

1.0.1.335:

- Added car mode selection to restore from crash or to switch to Dynamometer mode - Added panoramic roof calibration - Added ingress offsets setting - Added new ECUs to the database - Added VCM/TEM DIDs to control Backup battery status - Reworked entering to prog mode - Reworked DTC erase after programming - Reworked ECU sw reading - Fixed mistakenly shown GPF values for EV cars - Better BCM/BCM2 reconfiguration in case of incompatible configuration - Minor database update

1.0.1.318:

- Added NOx reduction system (AdBlue) adaptations reset - Stability improvements

1.0.1.310:

- Fixed oil level / temp values

1.0.1.309:

- Added partial support for LynkCo (Geely) cars - Added High Voltage (for PHEV) / Mid Voltage (for MHEV) battery SoC / SoH parameters - Added DIDs for MVBM module (for mild hybrid cars) - Added user defined service intervals - Database update - Fixed HVC opening for PHEV cars - Improved engine type detection - Minor stability / UI fixes

1.0.1.289:

- Added coolant temperature to Service / Engine window - Added TCM adaptation instructions - Added GPF indicator for gasoline cars to the main window (like DPF for diesel cars) - Additional fixes for engine type resolving

1.0.1.288:

- Improved compatibility with AAOS/iCup (Android) cars - Improved connection/reconnection stability - Added Combustion Preheater Module (CPM) unlock function (experimental) - Added Configuration filtering by the parameter id - Optimized ECU list panel, added automatic adjustment - Minor improvements on Diagnostics tab

1.0.1.283:

- DTC descriptions update

1.0.1.280:

- Display confirmed / unconfirmed DTCs separately using different colors. - DTC read mask settings.

1.0.1.277:

- Fixed AWD / DEM calibration routine. - Connection stability.

1.0.1.276:

- Added few BMS parameters to the Misc service dialog box, near to "BMS reset" button. - Added #377 carcfg parameter (missing in the database). It's still unknown, but some IHUs complain on 0 / Undefined value in it.

1.0.1.275:

- Prog mode enhancements. Should be good now. - VGM unlock fixes - Stability improvements

VTool home